| Modification card for: GL 291 F.ONLINE | Part No. : 161291 |
Rev.nr.: 01 Print Date: 23-11-01
| Date | Lev. | + |
Description |
| 01/11-92 | 1 |
1.machine like 281 level 17 but with new tanks, where heating elements are mounted on the side. Film width = 736,6mm | |
| 941110 | 2 |
No feed function altered to no feed light also on in on-line mode. | |
| 950525 | 3 |
Dry rack mounted with ground rollers. | |
| 950619 | 4 |
+ |
Angle for outlet sensor altered. |
| 951409 | 5 |
+ |
Process PCB altered. |
| 950918 | 6 |
+ |
Adjustable receiving basket. |
| 301195 | 7 |
Dev rack with PP+PA12 gear wheels. | |
| 960130 | 8 |
+ |
Fire proof PVC plate (217042) behind relay PCB. |
| 960130 | 9 |
XY condensator mounted near motor and earthed to ground via the middle leg. | |
| 960327 | 10 |
+ |
Bottom plates
fastened with 6x50 bolts + star locks. Back plate fastened with three extra screws near film out-let. |
| 960327 | 11 |
Transformer mounted outside the electronic box. | |
| 960417 | 12 |
PVC rollers in wet racks. | |
| 960612 | 13 |
+ |
New sensor angle mounted |
| 960624 | 14 |
Repl.pumps (66167)
altered from PTI to Gormann-rupp without diodes + earth wire mounted. |
|
| 960702 | 15 |
New motor 217217. ELVI with a blank housing. | |
| 961121 | 16 |
Spal circ.pumps replaced by IWAKI MD 20R-N | |
| 961128 | 17 |
+ |
Film transport altered mounted with two screws on gear wheel near namur sensor. Jumpers on process PCB altered |
| 961210 | 18 |
Wet racks mounted with 14 pvc rollers 129223 per rack. | |
| 970205 | 19 |
Cover in dry rack 129103 altered to insure better film transport. | |
| 970415 | 20 |
New speed PCB with creep speed. 911937 |
| 970415 | 21 |
Separate polished stainless steel guide mounted in dev inlet | |
| 970903 | 22 |
Metal covering plates. | |
| 971020 | 23 |
Filmtransport PCB altered. | |
| 980330 | 24 |
+ |
Springs used to hang repl. pumps. |
| 980330 | 25 |
Motor changed to 217216.Drive gear wheel mounted with new six sided (217305) cast hub using a wedge on the drive motor. | |
| 980330 | 26 |
New Fantech blowers with plastic wings in dry section. | |
| 980702 | 27 |
New outlet guide
129183 New outlet sensor 6095. |
|
| 980910 | 28 |
+ |
Process PCB altered to count 24 pulses in stead of 20. |
| 981001 | 29 |
New switch-box (217148) with automatic fuse mounted. | |
| 981101 | 30 |
+ |
New motor (217209) with needle bearings in gear box. |
| 981110 | 31 |
+ |
New 32T gear wheel in dry rack. |
| 990105 | 32 |
Edge strip (7105) mounted in dry inlet. | |
| 990312 | 33 |
Speed PCB with jumper to disengage creep speed. | |
| 990422 | 34 |
+ |
Edge strip altered prior to mounting, on the bottom in dry inlet. |
| 990506 | 35 |
+ |
Film transport PCB fitted with C11 to avoid error "0" |
| 991110 | 36 |
+ |
Lower rubber lip at Dry inlet fixed with rivets |
| 09-02-00 | 37 |
Wireing changed. Dryer blowers 136711, 136712 connected directly to relay PCB. Cable 217609 directly from relay PCB to pump support. Replenishment pumps in left side of machine |