| Modification card for: GL 361 F.ONLINE | Part No.: 161361
(White) (For grey machines serial no. higher than 9939479 see 161368.mod) |
Print Date: 12-03-02
| Date | Lev. | + |
Description |
| 01/02-93 | 1 |
1st
machine with electronic mounted under receiving basket same as GL171 161360 level 28. Mother boards aluminium plate acts as heat sink for the 15V stabilisator. Dev rack on-line version, with inlet guide . 1" soft roller inlet upper |
|
| 15/02-93 | 2 |
Fuse/ main switch box altered to 6 fuses and mounted 60cm. over floor level in accordance with IEC 204 norm. | |
| 15/03-93 | 3 |
Control panel altered to a rounder version. | |
| 01/05-93 | 4 |
New Bosch motor
with hexagon holed drive wheel. Speed PCB 911888. |
|
| 10/6-93 | 5 |
+ |
Motherboard modified to give repl. only when inlet sensor activated and not when on-line interface PCB starts mc: |
| 11/01-93 | 6 |
+ |
Ring type
springs (217334) in sted of type (65273) mounted on the rollers near the horizontal holes
in Dev Fix & wash racks. Springs on inlet rollers in Fix & Wash racks removed |
| 01/12-93 | 7 |
New temp. PCB 217097 | |
| 18/01-94 | 8 |
+ |
New IR PCB 911936 with tone decoder NE 567 |
| 20/01-94 | 9 |
Dev., fix and wash with 14 (136163) smooth PU rollers in sted of (61131) PU rollers. | |
| 01/06-94 | 10 |
Heating elements altered from 66606/66605 to 68545/68544.Seperate neutral wire connection to blowers in dry section. | |
| 01/07-94 | 11 |
New transformer 911241 4A with thermo fuse. | |
| 17/08-94 | 12 |
D4 mounted on relay PCB so as circ. pumps constantly on in operate and stand by, but not in night. | |
| 10/11-94 | 13 |
No feed function altered to No feed light also on in on-line mode. | |
| 14/09-95 | 14 |
Smooth rollers
(136361) used in wet racks. No nylon rollers used in wet racks . 1" rollers in crossover. |
|
| 18/09-95 | 15 |
Asdjustabel receiving basket. | |
| 30/11-95 | 16 |
Dev rack with PP+PA12 gear wheels. | |
| 30/01-96 | 17 |
+ USA |
Fire proof PVC plate (217042) behind relay PCB. |
| 30/01-96 | 18 |
XY condersator mounted near motor and earthed to ground via the middel leg. | |
| 27/03-96 | 19 |
+ |
Bottom plates
fastened with 6x50 bolts + star locks. Back plate fastened with three extra screws near film outlet. |
| 27/03-96 | 20 |
Transformer mounted outside the electronic box. | |
| 24/06-96 | 21 |
Repl.pumps (66167)
altered from PTI to Gormann-rupp without diodes + earth wire mounted. |
|
| 07/02-96 | 22 |
New motor 217217. ELVI with a blank housing. | |
| 21/11-96 | 23 |
Spal circ.pumps replaced by IWAKI MD 20R-N | |
| 15/04-97 | 24 |
New speed PCB with creep speed. 911937 | |
| 03/09-97 | 25 |
Metal covering plates. | |
| 21/11-97 | 26 |
Massave steel rollers (136544) in Dev, Fix and Wash racks. | |
| 30/03-98 | 27 |
Springs used to hang repl. pumps. | |
| 30/03-98 | 28 |
Motor changed to 217216.Drive gear wheel mounted with new six sided (217305) cast hub using a wedge on the drive motor. | |
| 30/03-98 | 29 |
New Fantech blowers with plastic wings in dry section. | |
| 10/01-98 | 30 |
+ |
New switch box (217148) with automatic fuse mounted. |
| 10/01-98 | 31 |
+ |
New motor (217209) with needle bearings in gear box. |
| 29/10-98 | 32 |
New tanks (for 5/8" hoses) mounted with fixation angles in tank . Cooler pipe in dev. | |
| 10/11-98 | 33 |
+ |
New 32T gear wheel in dry rack. |
| 15/12-98 | 34 |
+ |
Outlet guide in dry rack altered from 136103 to 136184 in connection with a shorter outlet angel on the dry end plate. |
| 05/01-99 | 35 |
+ |
Edge strip (7105) mounted in dry inlet. |
| 12/03-99 | 36 |
Speed PCB with jumper to disengage creep speed. | |
| 22/04-99 | 37 |
+ |
Edge strip altered prior to mounting, on the bottom in dry inlet. |
| 09-09-99 | 38 |
Racks
136816,136826,136836 R43 with 1 7/8" turnaround roller in bottom of rack |
|
| 991110 | 39 |
+ |
Lower rubber lip at Dry inlet fixed with rivets |
| 09-02-00 | 40 |
Wirering changed. Dryer blowers 136711, 136712 connected directly to relay PCB. Cable 217609 directly from relay PCB to pump support. Replenishment pumps in left side of machine |