| Modification card for: GOLD LINE 541 | Part No.: 161561 |
Print Date: 12-03-02
| Date | Lev. | + |
Description |
| 01/04-96 | 2 |
. | 1st mc: has the same first 41 mod levels as 161550 & the same first 20 levels as 161361 |
| 24/06-96 | 3 |
. | Repl.pumps (66167)
altered from PTI to Gormann-rupp without diodes + earth wire mounted. |
| 02/07-96 | 4 |
. | New motor 217217. ELVI with a blank housing. |
| 28/08-96 | 5 |
. | Asdjustabel receiving basket. |
| 21/11-96 | 6 |
. | Spal circ.pumps replaced by IWAKI MD 20R-N |
| 09/12-96 | 7 |
. | Dry rack altered to 155118 with alum. rollers. |
| 15/04-97 | 8 |
. | New speed PCB with creep speed. 911937 |
| 20/11-97 | 9 |
. | Dry rack altered to
smooth alum. Rollers. Gearing factor altered to80/25/25 |
| 12/01-98 | 10 |
. | Massave steel rollers (136544) in Dev, Fix and Wash racks. |
| 12/01-98 | 11 |
. | Fix spray as
standard. Light cover raised on 155783. |
| 30/03-98 | 12 |
. | Springs used to hang repl. pumps. |
| 30/03-98 | 13 |
. | Motor changed to 217216.Drive gear wheel mounted with new six sided (217305) cast hub using a wedge on the drive motor. |
| 30/03-98 | 14 |
. | New Fantech blowers with plastic wings in dry section. |
| 27/04-98 | 15 |
. | Metal covering plates. |
| 28/05-98 | 16 |
+ |
Adjustable angle mounted on fix spray. |
| 10/01-98 | 17 |
+ |
New switch-box (217148) with automatic fuse mounted. |
| 10/01-98 | 18 |
. | New motot(217209) with needle bearings in gear box. |
| 11/10-98 | 19 |
. | New 32T gear wheel in dry rack. |
| 18/11-98 | 20 |
. | Dev rack altered to
155908. Cross-over altered on Fix rack. Fix spray removed. |
| 05-01-99 | 21 |
. | Edge strip (7105) mounted in dry inlet. |
| 12/03-99 | 22 |
+ |
Speed PCB with jumper to disengage creep speed. |
| 15/03-99 | 23 |
+ |
Inlet roller in dry rack altered to pu. |
| 22/04-99 | 24 |
+ |
Edge strip altered prior to mounting, on the bottom in dry inlet. |
| 17/05-99 | 25 |
. | Same type 5/8" rollers used in Fix & Wash. |
| 15/06-99 | 26 |
. | New tanks 155610 Dev, 155612 water, 155613 fix with hose connections for 5/8" tubes. Both Dev and fix heating element is now 66107 . Tanks with fittings to reinforce the frame |
| 20/08/99 | 27 |
+ |
Lower input roller 155294 in Dev. rack changed to rubber to obtain more even pull in film |
| 10/11-99 | 28 |
+ |
Lower rubber lip at Dry inlet fixed with rivets |
| 6/12-99 | 29 |
. | Exhaust blower 70167, capacitor 29003 |
| 26/5-00 | 30 |
. | Wireing changed. Dryer blowers xxx711, xxx712 connected directly to relay PCB. Cable 217609 directly from relay PCB to pump support. Replenishment pumps in left side of machine |
| 7/11-01 | 31 | . |
New
version wet X |
| 21/12-01 | 32 | . | Dry rack: 25.0mm ALU roller 155474 with PVC endpieces using drive axele 80/25 is replaced by 25.4mm ALU roller 155275 using drive axle 79/24 gearwheels |