Dolev 800 Conveyor

Modification card for: DOLEV 800 CONVEYOR +INTERFACE

Part No. : 317710

Print Date: 12-03-02

Date

Lev.
+
Description

10/2-93 1 1^st conveyor

25/5-93 2 Upper roller altered to a 7/8" foam roller, and mounted with a spring.

1/9-93 3 + 5/8" steel roller used as film outlet guide.Roller fitted in altered angels to give place for a new cassette support with a better film transport.

17/9-93 4 + Cassette support lengthen in both directions. Mc: inlet sensor optomechanic 155308.

23/9-93 5 + Buffer guide made of two plate parts insted of a wire guide. Conv. connected to earth.

27/9-93 6 + Mc: inlet sensor altered to IR sensors.

1/10-93 7 Load switch starts mc.

25/11-93 8 + New interface PCB with adjustable buffer time.

30/11-93

9 + Extra 5/8"steel roller mounted in conv. inlet.
New mk.3 inlet guide 317752.

25/1-94 10 1 7/8" hard rubber roller altered to 1 7/8" ground.
PU roller 136483.

25/3-94 11 Screws in bottom inlet guide used to insure proper distance for film transport.

25/11-94
12
+ Delay between conv. switch and busy increased.

3/6-95 13 Solenoide used to lift buffer guide.
New interface PCB.
Fixed upper guide, axle fitted with counterbalance.

26/9-95 14 Counter balance increased to 155g.

24/2-97 15 Conv.case fitted with peep holes, to help when installing. Rubber grommets used to fill holes.

22/4-99 16 New dev. end plate (one piece) 317931
New conv. case 317941 ( no back plate)
New lower inlet guide 317743.
New upper inlet guide 317932

09-09-99 17 Drive motor fitted with 2 pc. 6.8uF capacitor instead of one to increase power for 7 mil (.18mm) film

06-12-99 18 Stronger solenoid 324037 new bracket 317804

03-01-00 19 + On EG processors pin 6 is disconnected in the plug for the Dolev, as it creates problems with early imagesetters.

Date	Lev.	+	Description
10/2-93	1		1^st conveyor
25/5-93	2		Upper roller altered to a 7/8" foam roller, and mounted with a spring.
1/9-93	3	+	5/8" steel roller used as film outlet guide.Roller fitted in altered angels to give place for a new cassette support with a better film transport.
17/9-93	4	+	Cassette support lengthen in both directions. Mc: inlet sensor optomechanic 155308.
23/9-93	5	+	Buffer guide made of two plate parts insted of a wire guide. Conv. connected to earth.
27/9-93	6	+	Mc: inlet sensor altered to IR sensors.
1/10-93	7		Load switch starts mc.
25/11-93	8	+	New interface PCB with adjustable buffer time.
30/11-93	9	+	Extra 5/8"steel roller mounted in conv. inlet. New mk.3 inlet guide 317752.
25/1-94	10		1 7/8" hard rubber roller altered to 1 7/8" ground. PU roller 136483.
25/3-94	11		Screws in bottom inlet guide used to insure proper distance for film transport.
25/11-94	12	+	Delay between conv. switch and busy increased.
3/6-95	13		Solenoide used to lift buffer guide. New interface PCB. Fixed upper guide, axle fitted with counterbalance.
26/9-95	14		Counter balance increased to 155g.
24/2-97	15		Conv.case fitted with peep holes, to help when installing. Rubber grommets used to fill holes.
22/4-99	16		New dev. end plate (one piece) 317931 New conv. case 317941 ( no back plate) New lower inlet guide 317743. New upper inlet guide 317932
09-09-99	17		Drive motor fitted with 2 pc. 6.8uF capacitor instead of one to increase power for 7 mil (.18mm) film
06-12-99	18		Stronger solenoid 324037 new bracket 317804
03-01-00	19	+	On EG processors pin 6 is disconnected in the plug for the Dolev, as it creates problems with early imagesetters.