| Modificationcard for: Scangraphic Futuro conv/interf | Part No. : 454510 |
Print Date: 12-03-02
| Date | Lev. | + | Description |
| 20/5-97 | 1 | 1st mc sent to Scangraphic. | |
| 25/6-97 | 2 | Adapter altered for
better light lock. Special light lid on Dev rack. |
|
| 28/8-97 | 3 |
New upper outlet
guide. New rack side (plate), adpator, lid and cassett lid. |
|
| 15/9-97 | 4 |
+ |
Switch mounted on conv. |
| 1/10-97 | 5 |
+ |
Interface PCB altered.Speed control on PCB altered. |
| 1/10-97 | 6 |
+ |
Adapter rack altered. |
| 31/10-97 | 7 |
+ |
Locking device
mounted on adpator. Guide in adpator altered to rust free (el. Polished ) steel.Rollers altered to soft rubber and PU. Teflon tape mounted on adaptor outlet guide |
| 19/12-97 | 8 |
+ |
New locking device version B Mounted in conv. |
| 19/12-97 | 9 |
Gear wheel on motor
altered to 44T. New interface PCB 454558. |
|
| 5/3-98 | 10 |
+ |
Extra blockage on bottom of adaptor rack. |
| 13/3-98 | 11 |
+ |
Extra plastic bricks
mounted on rack side plates. Alterations on adaptor covering plate. |
| 12/8-98 | 12 |
+ |
New aluminiun adaptor rack. |
| 12/8-98 | 13 |
+ |
Extra diode mounted on interface PCB. |
| 12/8-98 | 14 |
New conv. with two
motors. New interface PCB. |
|
| 8/2-99 | 15 |
New conv.PCB with reset swich. | |
| 8/2-99 | 16 |
+ |
Guide 454523 altered. |
| 25/2-99 | 17 |
+ |
Alterations on
interface PCB. Peel ic mounted. Software altered. |
| 22/3-99 | 18 |
+ |
Alterations on interface PCB. C1 removed. R8 altered to220K. |
| 22/3-99 | 19 |
+ |
3 extra 8mm. Washers mounted near motor. |
| 31/3-99 | 20 |
+ |
Software altered tback to original from 1998. |
| 14/4-99 | 21 |
+ |
New Peel software. |
| 9/06-99 | 22 |
Conveyor motor
replaced with motor 70161 Not important as service issue |
|
| 25/11-99 | 23 |
+ |
Gasspring 454237
changed to 454227 in one side. New gasspring has safetylock mechanism. See servicebulletin |
| 16/3-00 | 24 |
New gasspring 150N
part no.447238 Bracket on processor with eyes in the upper end |
|
| 17/8-00 | 25 |
+ |
Interface PCB changed
to maske motor 2 run slow at FEED signal after cut, to eliminate Z-fold at processor entrance |
| 13/9-00 | 26 |
+ |
Adapted for FUTURO
NEWS with film speed 6.27m/min (0ld Futuro 5.02 m/min) Timing belt pulley on first 2 sets of conv rollers changed from 30T to 16Teeth Shorter timing belt 320XL # 464476 New interface PCB 454659 |
| 24/10-00 | 27 |
+ |
Interface PCB fitted with extra potmeter and other changes. Ready is issued only after conv sw. is deactivated |
| 10/11-00 | 28 |
+ |
16T timing belt pulleys in aluminium 129255 with one way bearings |
| 14/06-01 | 29 | + | Interface changed with software 890719 v 1.03 and 890720 v. 104 . Conveyor resets itself after 45 sec in case of a false cut situation. Cut will only be accepted up to 7 sec after FEED. Part #454659 |