| Modification card for: Purup 36" online | Part No.: 161370 |
Print Date: 12-03-02
| Date | Lev. | + |
Description |
| 18/01-95 | 1 |
1st mc: has the same first 10 mod.levels as 161361 | |
| 07/06-95 | 2 |
Plotter cable altered to avoide showing error on Purup. | |
| 19/06-95 | 3 |
+ |
Inlet sensor adjustment altered. |
| 14/09-95 | 4 |
Smooth rollers136361
in wet racks. No nylon rollers in wet racks. 1" roller in cross over. |
|
| 18/09-95 | 5 |
Asdjustabel receiving basket. | |
| 03/11-95 | 6 |
+ |
Mains connection on relay PCB altered. |
| 03/11-95 | 7 |
Fastning plate mounted with angels, for bearings used by diverter. | |
| 14/11-95 | 8 |
Interface PCB and cable prepared for diverter. | |
| 30/11-95 | 9 |
+ |
Dev rack with PP + PA12 gear wheels. |
| 16/01-96 | 10 |
+ |
Filmtransportcontrol diablet |
| 30/01-96 | 11 |
XY condersator mounted near motor and earthed to ground via the middel leg. | |
| 30/01-96 | 12 |
UL outlet sensor removed | |
| 27/03-96 | 13 |
+ |
Bottom plates
fastened with 6x50 bolts + star locks. Back plate fastened with three extra screws near film out-let. |
| 24/06-96 | 14 |
Repl.pumps
(66167) altered from PTI to Gormann-rupp without diodes + earth wire mounted. |
|
| 02/07-96 | 15 |
New motor 217217. ELVI with a blank housing. | |
| 12/09-96 | 16 |
Transformer with 208/230V primary inlet. USA and Korea must be connected to 208V. | |
| 21/11-96 | 17 |
Spal circ.pumps replaced by IWAKI MD 20R-N | |
| 16/06-97 | 18 |
+ |
Exhaust blower 70148 altered to a larger blue blower 65154 |
| 18/12-97 | 19 |
Voltage stabilizer on CPU board altered to type LA940V5. | |
| 16/02-98 | 20 |
Metal covering
plates. Ps. Mc. 161373, 161380, 161381, & 161382 have metal plates from mod. Level 20. |
|
| 16/02-98 | 21 |
Suction canal 217006 mounted near dev section to stop fumes from entering the plotter. | |
| 05/03-98 | 22 |
+ |
Diode mounted on CPU board. |
| 30/03-98 | 23 |
Repl. pumps mounted with springs. | |
| 30/03-98 | 24 |
Motor changed to 217216.Drive gear wheel mounted with new six sided (217305) cast hub using a wedge on the drive motor. | |
| 30/03-98 | 25 |
New blowers mounted in dry section. | |
| 01/10-98 | 26 |
+ |
New switch box (217148) with automatic fuse mounted. |
| 01/10-98 | 27 |
New drive motor 217209 with needle bearings. | |
| 29/10-98 | 28 |
New tanks with pipes
for 5/8" hose and fixture angels. Coller pipe in water tank. |
|
| 10/11-98 | 29 |
New 32T gear wheel in dry rack. | |
| 05/01-99 | 30 |
Edge strip 7105 mounted in dry inlet | |
| 22/04-99 | 31 |
+ |
Edge strip altered prior to mounting, on the bottom in dry inlet. |
| 10/11-99 | 32 |
+ |
Lower rubber lip at dry inlet fixed with rivets |